Even if the Android platform changes the more time passes, it still happens to suffer bugs ... Some are not particularly problematic and will not impact you very little in your daily life when others may on the contrary prevent you completely from use your Blackview A60. In this guide, we are going to tell you about a bug that fortunately only affects a few devices, nevertheless which is very disturbing. This is a startup bug, when you turn your phone back on, it gets stuck on the logo.
In this guide, we will therefore explain to you How to fix a Blackview A60 stuck on logo on startup? To do this, we will first of all try to interpret with you the origin of this bug, then, then, to present all the procedures at your disposal to unlock your Blackview A60 stuck on android logo.
Why does my Blackview A60 get stuck on the Android logo when switching on?
We start this guide by seeing the reason why your Blackview A60 gets stuck on the Android logo on ignition? This bug is particularly disabling because it prevents you from performing any operation on your phone and moreover you will not even be able to complete the start-up process, your Blackview A60 will therefore be completely unusable.
The reasons for this bug can be many, although regularly it is following an update that a Blackview A60 hangs on the logo on ignition. It is usually a problem during the installation of the data that will trigger this bug. Sometimes, it is after a fall, an immersion in water that the bug can happen. In these cases, it is unfortunately not possible to do much outside to take your Blackview A60 to a repairman because it is surely components which have been affected which are responsible for the problem. The battery is sometimes the component of concern, you can check the battery status of your Blackview A60.
That said, we have already seen cases where the origin is more vague, no recent update installed, no drop ... In these situations, as for a problem following an update, our solutions will help you, discover them below.
How to fix my Blackview A60 stuck on Android logo on power up?
We now move on to the solutions part of our small file, and we will present you three different methods, from the easiest to perform to the most complicated for fix your Blackview A60 stuck on Android logo.
Force stop your Blackview A60
First of the alternatives, the simplest. You have surely tried to restart your Blackview A60 by leaving the “Power” button on the latter pressed for a few moments. If this action had no effect you will have to use the forced restart. You may not know this manipulation, however, it is very simple and aims to restart a phone even if it has a bug. If this solution does not work, you can try another solution to force the shutdown of your Blackview A60, the goal being to turn it off so that the bug disappears when you restart it:
- To force restart your Blackview A60, keep your finger pressed on the "Power" key for 10 seconds
- In the event that this does not work, wait for the battery of your Blackview A60 to discharge completely to try to turn it on again once it has been turned off
Wipe Cache of your Blackview A60
In the event that the first manipulation did not work, we will move on to advanced solutions. We will go through the recovery mode of your Blackview A60 to unlock it. This mode is particularly practical in the event that you are the victim of a bug, in the event that you wish to reset your smartphone ... In this part, we will perform a Wipe Cache which will correspond to cleaning the entire cache memory of your Blackview A60 and therefore repairing any bugs:
- Turn off your Blackview A60, or wait for the battery to drain completely
- Recharge it more than 50%
- Hold the key "High Volume" and the button "Power" pressed for several moments until you see this very basic menu appear on the screen
- Navigate with the volume keys to "Wipe Cache Partition"
- Confirm the operation with the "Power" key
- Now select, "Reboot System Now" to restart your Blackview A60
Factory reset your Blackview A60 to unlock it
In the event that the first solution did not work, we will be even more radical, you will however lose all the data stored on your Blackview A60, despite everything if it is unusable, you will not be able to do anything anyway. to recover. It's up to you to decide if you prefer to try to go see a repairer or do the technique yourself if you have already saved all your data:
- Switch off your Blackview A60 or wait for it to switch off on its own when the battery is empty
- Make sure it has more than 50% battery
- Access recovery mode with the technique seen in the previous part
- Go to the option "Wipe Data / Factory Reset" with the volume keys, and confirm the operation with the power button
- Finish the technique by choosing the option "Reboot System Now"
If you are looking for a lot of tutorials to become the king of the Blackview A60, we invite you to explore the other tutorials in the category: Blackview A60.
