Although the Android platform changes over time, it is unfortunately not uncommon to experience bugs... Some are not completely problematic and will only disturb you very little in your daily life when others may, on the contrary, completely prevent you to use your Blackview BV7100. In this article, we are going to tell you about a bug which fortunately only affects a few devices, but which is very disturbing. This is a startup bug, when you turn on your mobile phone, it remains stuck on the logo.
So in this article we will show you How to fix a Blackview BV7100 stuck on logo on startup? To do this, we will first of all try to understand with you the nature of this bug, then, to reveal to you all the procedures at your disposal to unlock your Blackview BV7100 stuck on android logo.
Why does my Blackview BV7100 get stuck on the Android logo when switching on?
We start this guide by discovering why your Blackview BV7100 remains stuck on the Android logo when switching on? This bug is particularly disabling because it prevents you from carrying out the slightest operation on your mobile phone and moreover you will not even be able to complete the start-up process, your Blackview BV7100 will therefore be completely unusable.
The causes of this bug can be various, even if, regularly it is after an update that a Blackview BV7100 hangs on the logo when switching on. It is most of the time a problem at the time of the installation of the data which will trigger this bug. Sometimes it is after a fall, an immersion in water that the bug can happen. In these cases, it is unfortunately not possible to do much except to take your Blackview BV7100 to a repairman since it is probably components that have been affected that are causing the problem. The battery is sometimes the problematic component, you can check the battery status of your Blackview BV7100.
That said, we have already seen cases where the nature is more blurry, no recent update installed, no drop ... In these cases, as for a problem following an update, our solutions will help you, discover the following.
How to fix my Blackview BV7100 stuck on Android logo when turning on?
We now move on to the solutions part of our article, and we will reveal three different solutions, from the easiest to achieve to the most complicated for repair your Blackview BV7100 stuck on Android logo.
Force stop your Blackview BV7100
First of the alternatives, the simplest. You have probably tried to restart your Blackview BV7100 by pressing the “Power” button on it for a few seconds. If this manipulation does not work, you will have to use the forced restart. You may not be familiar with this manipulation, however it is very simple and aims to restart a mobile phone even if it bugs. If this solution does not work, you can try another technique to force your Blackview BV7100 to shut down, the objective being to turn it off so that the bug disappears during the restart:
- To force restart your Blackview BV7100, keep your finger pressed for 10 seconds on the "Power" key
- If that doesn't work, wait for the battery of your Blackview BV7100 to discharge completely to try to turn it back on once turned off
Make a Wipe Cache of your Blackview BV7100
If the first solution didn't work, we'll move on to advanced solutions. We will go through the recovery mode of your Blackview BV7100 to unlock it. This mode is particularly useful in the event that you experience a bug, in the event that you want to reset your phone... In this part, we are going to perform a Wipe Cache which corresponds to cleaning all the cache memory of your Blackview BV7100 and therefore repairing any bugs:
- Turn off your Blackview BV7100, or wait for the battery to discharge completely
- Recharge it more than 50%
- Hold the key "High Volume" and the button "Power" pressed for several seconds until you see this very basic menu appear on the screen
- Navigate with the volume keys to "Wipe Cache Partition"
- Validate the operation with the "Power" key
- Now select "Reboot System Now" to restart your Blackview BV7100
Perform a Factory Reset of your Blackview BV7100 to unlock it
If the first technique did not work, we are going to be even more radical, you will however lose all the data saved on your Blackview BV7100, that said if it is unusable, you will not be able to recover anything in any case. It's up to you whether you prefer to try to go see a repairer or carry out the procedure yourself if you have already backed up all your data:
- Turn off your Blackview BV7100 or wait for it to turn off by itself when the battery is discharged
- Make sure it has more than 50% battery
- Access recovery mode with the procedure seen in the previous part
- Go to the option "Wipe Data / Factory Reset" with the volume keys, and validate the operation with the power button
- Finish the procedure by choosing the option "Reboot System Now"
If you are ever looking for as many tutorials as possible to become the king of the Blackview BV7100, we invite you to explore the other tutorials in the category: Blackview BV7100.
