Even if the Android platform changes over time, it still happens to suffer bugs ... Some are not particularly problematic and will not disturb you in your daily life when others will be able to completely prevent you from use your Crosscall TREKKER-M1. In this article, we are going to tell you about a bug that fortunately only affects a few devices, nevertheless which is very disturbing. This is a startup bug, when you turn your phone back on, it gets stuck on the logo.
So in this article we will show you How to fix a Crosscall TREKKER-M1 stuck on the logo on startup? For that, we will first try to understand with you the cause of this bug, then, to present all the procedures that you can carry out to unlock your Crosscall TREKKER-M1 stuck on the Android logo.
Why does my Crosscall TREKKER-M1 get stuck on the Android logo on startup?
We therefore begin this article by seeing the reason why your Crosscall TREKKER-M1 gets stuck on the Android logo at startup? This bug is really disabling because it prevents you from performing any action on your phone and moreover you will not even be able to complete the startup process, your Crosscall TREKKER-M1 will therefore be totally unusable.
The causes of this bug can be various, even if, regularly it is after an update that a Crosscall TREKKER-M1 hangs on the logo at startup. It is usually a problem during data installation that causes this bug. Sometimes, it is after a fall, an immersion in water that the bug can happen. In these cases, it is unfortunately not possible to do much outside to take your Crosscall TREKKER-M1 to a repairer because it is surely components which are damaged which are responsible for the problem. The battery is sometimes the component of concern, you can check the battery status of your Crosscall TREKKER-M1.
Despite everything, we have already seen cases for which the cause is less obvious to distinguish, no recent update installed, no fall ... In these cases, as for a problem following an update, our solutions will help you, discover the following.
How to fix my Crosscall TREKKER-M1 stuck on the Android logo when turning on?
We now move on to the solutions part of our post, and we will present you three different techniques, from the easiest to implement to the most complicated for repair your Crosscall TREKKER-M1 stuck on Android logo.
Force stop your Crosscall TREKKER-M1
First of the alternatives, the simplest. You have no doubt tried to restart your Crosscall TREKKER-M1 by keeping the “Power” button pressed for a few seconds. In the event that this manipulation does not work, you will have to use the forced restart. You may not know this technique, however it is very simple and aims to restart a phone even if it bugs. If this solution does not work, you can try another technique to force the shutdown of your Crosscall TREKKER-M1, the objective being to turn it off so that the bug disappears when you restart it:
- To force restart your Crosscall TREKKER-M1, keep your finger pressed on the "Power" key for 10 seconds
- In the event that this does not work, wait until the battery of your Crosscall TREKKER-M1 drains to try to restart it once it is off
Wipe Cache of your Crosscall TREKKER-M1
In the event that the first technique did not work, we will move on to advanced solutions. We will go through the recovery mode of your Crosscall TREKKER-M1 to unlock it. This mode is really useful in the event that you are the victim of a bug, in the event that you wish to reset your device ... In this part, we will perform a Wipe Cache which will correspond to cleaning the entire cache memory of your Crosscall TREKKER-M1 and therefore repairing any bugs:
- Switch off your Crosscall TREKKER-M1, or wait for the battery to drain completely
- Recharge it more than 50%
- Hold the key "High Volume" and the button "Power" pressed for several seconds until you see this very basic menu appear on the screen
- Navigate with the volume keys to "Wipe Cache Partition"
- Validate the operation with the "Power" key
- Select now "Reboot System Now" to restart your Crosscall TREKKER-M1
Factory reset your Crosscall TREKKER-M1 to unlock it
In the event that the first technique does not work, we will be even more radical, you will however lose all the data stored on your Crosscall TREKKER-M1, that said if it is unusable, you will not be able to do what that nothing happens to recover. It's up to you to decide if you prefer to try to go see a repairer or carry out the procedure yourself if you have already saved all your data:
- Switch off your Crosscall TREKKER-M1 or wait for it to switch off by itself when the battery is discharged
- Check that it has more than 50% battery
- Access recovery mode with the procedure seen in the previous part
- Go to the option "Wipe Data / Factory Reset" with the volume keys, and validate the manipulation with the power button
- Finish the procedure by choosing the option "Reboot System Now"
If you want as many tutorials as possible to become the king of Crosscall TREKKER-M1, we invite you to watch the other tutorials in the category: Crosscall TREKKER-M1.
