Although the Android platform changes over the years, it still happens to encounter bugs... Some are not particularly problematic and will only disturb you very little in your daily life when others may, on the contrary, completely prevent you from using your Nope. In this guide, we are going to tell you about a bug which, despite everything, only affects a few devices, but which is very disturbing. This is a startup bug, when you turn your phone back on, it gets stuck on the logo.
So in this guide we will show you how to fix nan stuck on logo on startup? For that, we will first try to interpret with you the origin of this bug, and then, to expose you all the alternatives which you can carry out for unlock your nan stuck on android logo.
The reason why my nan gets stuck on android logo on boot?
We therefore start this guide by discovering the reason why your nan gets stuck on android logo on boot? This bug is really disabling because it prevents you from performing the slightest action on your phone and moreover you will not even be able to finalize the start-up process, your nan will suddenly be completely unusable.
The reasons for this bug can be many, although often it is following an update that a nan hangs on the logo at startup. It is in most cases a problem during the installation of the files that triggers this bug. Sometimes, it is following a fall, immersion in water that the bug can happen. In these cases, it is unfortunately not possible to do much except to take your nan to a repairer because it is probably components that have been touched that are responsible for the problem. The battery is sometimes the component that causes concern, do not hesitate to check the battery status of your nan.
Despite everything, we have already observed cases where the origin is more vague, no recent update installed, no drop ... In these situations, as for a problem following an update, our solutions will help you, discover the following.
How to fix my nan stuck on android logo when turning on?
We now move on to the solutions part of our little file, and we will show you three different methods, from the simplest to implement to the most complicated to fix your nan stuck on android logo.
Force stop your nan
First of the solutions, the easiest. You have certainly tried to restart your nan by holding down the “Power” button on it for a few moments. In the event that this manipulation has had no effect, you will have to use the forced restart. You may not be familiar with this manipulation, but it is very simple and aims to restart a phone even if it bugs. If ever this solution does not work, you can try another solution to force stop your nan, the objective being to turn it off so that the bug is no longer present at the time of the next restart:
- To force restart your nan, keep your finger pressed for 10 seconds on the "Power" key
- If it ever doesn't work, wait for your nan's battery to drain to try restarting it once turned off
Make a Wipe Cache of your nan
If the first solution did not work, we will move on to advanced solutions. We will go through the recovery mode of your nan to unlock it. This mode is really practical if you are ever the victim of a bug, if you ever want to reset your phone... In this part, we are going to perform a Wipe Cache which will correspond to a cleaning of all the cache memory of your nan and therefore repair any bugs:
- Turn off your nan, or wait for the battery to completely drain
- Recharge it more than 50%
- Hold the key "High Volume" and the button "Power" pressed for several moments until you see this very basic menu appear on the screen
- Navigate with the volume keys to "Wipe Cache Partition"
- Confirm the operation with the "Power" key
- Select now "Reboot System Now" to restart your nan
Perform a Factory Reset of his nan to unlock him
If ever the first solution did not work, we are going to be even more radical, you will still lose all the data saved on your nan, despite everything if it is unusable, you will not be able to recover anything in any case . It's up to you whether you prefer to try going to see a repairer or to carry out the process yourself if you have already backed up all your data:
- Turn off your nan or wait for it to turn itself off when the battery is empty
- Check that it has more than 50% battery
- Access the recovery mode with the procedure explained in the previous part
- Go to the option "Wipe Data / Factory Reset" with the volume keys, and validate, the manipulation with the power button
- Finish the process by choosing the option "Reboot System Now"
In the event that you want a maximum of tutorials to become the king of nan, we invite you to browse the other tutorials in the category: nan.
