Although the Android platform changes over time, it is unfortunately not uncommon to experience bugs ... Some are not completely problematic and will not disturb you in your daily life when others will, on the contrary, prevent you from doing anything. using your Wiko VIEW. Today we are specifically going to tell you about a bug which however only affects a few devices, however which is very disturbing. This is a startup bug, the moment you turn your phone back on it gets stuck on the logo.
So today we will show you How to fix a Wiko VIEW stuck on logo on startup? In this context, we will first try to understand with you the origin of this bug, and then, to reveal all the procedures that you can carry out to unlock your Wiko VIEW stuck on Android logo.
Why does my Wiko VIEW get stuck on the Android logo on startup?
We therefore start this article by discovering why your Wiko VIEW gets stuck on the Android logo at startup? This bug is particularly annoying because it prevents you from performing any action on your phone and, moreover, you will not even be able to finalize the start-up process, your Wiko VIEW will therefore be completely unusable.
The origins of this bug can be numerous, although often it is following an update that a Wiko VIEW hangs on the logo at startup. It is usually a problem during the installation of the files that causes this bug. Sometimes, it is after a fall, an immersion in water that the bug can happen. In these cases, however, it is not possible to do much outside to take your Wiko VIEW to a repairman Since it is undoubtedly components which are damaged which are at the origin of the concern. The battery is sometimes the component that causes concern, do not hesitate to check the battery status of your Wiko VIEW.
Despite everything, we have already observed cases where the origin is more vague, no recent update installed, no drop ... In these situations, as for a problem following an update, our solutions can help you, discover the following.
How to fix my Wiko VIEW stuck on the Android logo when turning on?
We now move on to the solutions part of our small file, and we will reveal three different methods, from the easiest to implement to the most complex for repair your Wiko VIEW stuck on Android logo.
Force stop your Wiko VIEW
The first of the alternatives, the easier. You have no doubt tried to restart your Wiko VIEW by holding down the “Power” key on the latter for a few moments. If this action does not work you will have to use the forced restart. You may not know this solution however it is very simple and aims to restart a phone even if it bugs. In the event that this solution does not work, you will be able to try another technique to force the shutdown of your Wiko VIEW, the goal being to turn it off so that the bug disappears during restart:
- To force restart your Wiko VIEW, keep your finger pressed on the "Power" key for 10 seconds
- In the event that this does not work, wait for the battery of your Wiko VIEW to empty to try to restart it once it is off
Perform a Wipe Cache of your Wiko VIEW
In the event that the first technique did not work, we will move on to advanced solutions. We will go through the recovery mode of your Wiko VIEW to unlock it. This mode is particularly useful in the event that you experience a bug, in the event that you wish to reset your phone ... In this part, we are going to perform a Wipe Cache which corresponds to cleaning the entire cache of your Wiko VIEW and therefore repairing any bugs:
- Turn off your Wiko VIEW, or wait for the battery to drain completely
- Recharge it more than 50%
- Hold the key "High Volume" and the button "Power" pressed for several moments until you see this very basic menu appear on the screen
- Navigate with the volume keys to "Wipe Cache Partition"
- Confirm the operation with the "Power" key
- Now select "Reboot System Now" to restart your Wiko VIEW
Factory reset your Wiko VIEW to unlock it
In the event that the first technique does not work, we will be even more radical, however, you will lose all the data stored on your Wiko VIEW, despite everything if it is unusable, you will be able to do nothing. nothing happens to recover. It's up to you to decide if you prefer to try to go see a repairer or carry out the procedure yourself if you have already backed up all your data:
- Turn off your Wiko VIEW or wait for it to turn off by itself when the battery is empty
- Check that it has more than 50% battery
- Access recovery mode with the procedure seen in the previous part
- Go to the option "Wipe Data / Factory Reset" with the volume keys, and validate, the manipulation with the power button
- Finish the procedure by choosing the option "Reboot System Now"
In the event that you are looking for as many tutorials as possible to become the absolute master of the Wiko VIEW, we invite you to watch the other tutorials in the category: Wiko VIEW.
